熱門關鍵詞：濟南彩鋼板 | 濟南復合板 | 濟南彩鋼瓦 | 濟南c型鋼 | 濟南鋼結構 |
The characteristics of color steel plate and the installation mode of color steel plate are mainly explained from the following aspects, hoping to help you.
A. ) the color steel plate can be disassembled and restored, which is convenient for assembly and disassembly. The standard unit wall panels can be interchanged, which is very convenient for maintenance, water and electricity, line transformation, etc.
Henan color steel plate manufacturer
B) The color steel plate surface can be perforated arbitrarily, which is very convenient for installing control switches, power sockets and other devices without additional treatment.
C) The surface color of the color steel plate is soft, forming a unified and harmonious whole with the floor and ceiling, making the whole space modern.
D) The electrostatic baking paint spraying process is adopted, with smooth and fine surface, no dust accumulation and simple maintenance, which meets the cleanliness requirements of the machine room.
E) The color steel plate meets the class a fire protection standard of the national standard and can fully meet the fire protection requirements for the construction and decoration of the machine room.
Installation method of color steel plate
1）放樣：依圖面及現場實測尺寸進行放樣（隔墻中 心線）以兩收邊中 心線與地面的交點彈出地軌中 心線。應 這四條線處在一個垂直面內，以 以后安裝之墻面的垂直。
1) Setting out: setting out shall be carried out according to the drawing surface and on-site measured dimensions (partition center line), and the ground rail center line shall be snapped at the intersection of the two trimming center lines and the ground. These four lines shall be in a vertical plane to ensure the perpendicularity of the wall to be installed later.
2) Overhead rail: the installation shall be neat, the interface shall be reinforced and repaired, and fixed on the cement ceiling with screws or screws every 500mm-600mm.
3) Ground rail: when installing the ground rail, reserve the installation position of the door first, and pay attention to the ground difference. If the ground height difference is too large, it shall be leveled to reduce the drop without affecting the adjustment level. It shall be fixed on the floor with blows or screws every 600mm. If the ground joint is too large, it shall be filled with joint sealant.
4) Edge trimming: cut the edge trimming according to the actual measured value, and trim the edge after cutting. Strive to be neat and consistent, and the joints shall be free of gaps. Pay special attention to the interface with the ceiling and skirting board, and make sure there is no gap.
5) Vertical keel: set a vertical keel every 49cm (half the size of the partition). The columns on both sides of the door frame are completely fixed up and down without shaking. Add a vertical keel in the opposite direction. The width of the door leaf exceeds 90cm. The horizontal columns on the door frame must be strengthened and fixed by welding if necessary.
Henan color steel plate manufacturer
6) Transverse through keel: if the height is more than 3m, one keel shall be set at 1.2m in the vertical direction. When the two branches are connected, they must be overlapped, and the overlapping length shall not be less than 10cm.
7) Wallboard: color steel plates shall be installed from one side in sequence, and the spacing between connected plates shall be 12mm. 12mm wide battens are used between diaphragms, and standard unit wallboards can be interchanged.
Precautions for installation: 12mm wide battens are used between the panels, and the standard unit wall panels can be interchanged. Pay more attention to the details when installing the wall panels. First, transport the wall panels to the vicinity of the installation point with a pallet truck, and then use a suction cup to stand the metal plates upright, so that the lower end rests against the skirting plate, the two sides of the lining plate are close to the vertical keel, the spacing between one side and another wall panel is 12mm, and use a fixing piece to lean against it, Then fix the self tapping screws on the vertical keel with a fixed spacing of 300mm-400mm. Pay attention to the horizontal and vertical during assembly. When the latter wall panel needs to be cut, if it needs to be cut, measure the size, cut and trim it in the correct way, and install it on the wall.
The wonderful contents of this article are provided by Jinan color steel plate. There are many wonderful contents on this website. You can click to enter more contents: http://www.cheholam.com We have special customer service to answer your questions